£200 off orders over £2,000 until 31st March
Use code SAVE200
0345 22 22 990

There are no items in your shopping cart.

800mm - 1200mm Wide Slimline Base Cabinet D450mm Assembly Instructions

Click here if you would like to download a pdf of these instructions.

IMPORTANT - Please read prior to installation

Thanks for purchasing a solid oak kitchen cabinet. Before you commence installation, please check the contents of this package to ensure that all necessary components are included. Please contact us immediately via email if any parts appear to be missing.

Please ensure that you assemble the goods in a clean, dry area, with plenty of space, and that you have the correct tools and equipment to hand. We recommend that you read the instructions in full before you commence assembly, and if necessary, run through the installation procedure without physically assembling any items before you begin. Only construct one cabinet at a time, and follow the installation stages in order, without modification. During installation, be careful to keep the relevant fittings for the current cabinet together. Do not over tighten screws, and ensure that any larger panels are laid flat and protected.

Clean the cabinets with a damp cloth, and if necessary a small amount of liquid soap, only. Do not use abrasives. We provide a full cleaning and aftercare guide on our website, please view this for further information.

Wide Slimline Base Cabinet D450mm


Wide Slimline Base Cabinet D450mm Panels


Wide Slimline Base Cabinet D450mm hardware

Step one:

Insert [A] and [E] as shown in the diagram below.

Apply a small drop of glue to each dowel [E] before inserting.

Wide Slimline Base Cabinet D450mm - step one

Step two:

Insert [B] as shown ensuring the arrow marking is pointing towards the outside edge.

Wide Slimline Base Cabinet D450mm - step two

Step three:

Connect the base panel (3) to the side panel (1) using the fittings inserted during steps 1 and 2.

Repeat the process for all top panels (2)

Wide Slimline Base Cabinet D450mm - step three

Step four:

Fit support panel (6) using 4 x [E] dowels and secure with 2 x [D] screws.

Wide Slimline Base Cabinet D450mm - step four

Step five:

Connect the opposite side panel (1) as shown then tighten all fittings [B] by turning in direction of arrow with a screwdriver.

Wide Slimline Base Cabinet D450mm - step four

Step six:

Slide the back panel (4) between the grooves on the inside edge of each side panel (1) as shown.

It is advised that you run a small amount of glue along the grooves first.

Wide Slimline Base Cabinet D450mm - step six

Fitting Cabinet Legs:

Position each foot mount [H] towards the edge of the base panel at each corner. Ensure screw holes are not aligned over the panel join and that the overhand foot support is overlapping the side panel as shown below.

Drill 3mm pilot holes into the base panel through the four mounting holes in each foot mount. Now screw the four [C] screws supplied with each foot directly through the foot mount and into the base panel.

Attach the adjustable legs [I] to each foot mount and adjust to the appropriate height.

fitting cabinet legs

Joining Cabinets:

Cabinets should be joined between each set of hinge holes on the inside edge of the side panel as shown in the diagram. Mark 25mm as a guide on a 3mm diameter drill bit using masking tape. Drill between the hinge holes into the cabinet side panel (18mm) and 7mm into the next until you reach the marker. Join the two cabinets together using the 25mm screws provided [D]

joining cabinets

Fitting Cabinet to Wall:

When fixing the cabinet to the wall you must only use slotted angle brackets. A round head screw must be used to fix the bracket.
It is important that you use the slot that runs at perpendicular to the width (across and not parallel with the grain).

fitting cabinet to wall

Fitting Shelves:

Push the shelf supports [F] into the pre-drilled shelf holes then sit the shelf on top.

fitting shelves

Fitting Plinths:

Secure plinth to plinth clip [J] using screw provided (C).
Clip each plinth clip onto the legs [I] at the front of the cabinet.

fitting plinths
back to the topBack to Top

Easy to buy online - Follow our 4 simple steps to order your kitchen

choose your door type and finishPick from 'Shaker' or 'Traditional' door styles; available in a choice of sanded, lacquered, or painted finishes (using Farrow & Ball colours).Choose your door type and finish. choose your drawer typesNext pick from a comprehensive range of oak drawers, including single and double height, with a choice of oak, stainless steel or standard grey sides.Choose your drawer type. Add your unit and accessoriesFinally, choose suitable solid oak cabinets, additional specialist units and matching accessories from our wide range, then finalise your order.Add your units to the basket. Get your kitchen within 10 daysOnce your order is complete our specialist team will deliver your order direct to your door within 10 working days.Receive your kitchen within 10 working days!