10% off everything until 31st January
Code: SAVE10
0345 22 22 990

There are no items in your shopping cart.

300mm - 600mm Wide 2145mm Full Height Cabinet Assembly Instructions

Click here if you would like to download a pdf of these instructions.

IMPORTANT - Please read prior to installation

Thanks for purchasing a solid oak kitchen cabinet. Before you commence installation, please check the contents of this package to ensure that all necessary components are included. Please contact us immediately via email if any parts appear to be missing.

Please ensure that you assemble the goods in a clean, dry area, with plenty of space, and that you have the correct tools and equipment to hand. We recommend that you read the instructions in full before you commence assembly, and if necessary, run through the installation procedure without physically assembling any items before you begin. Only construct one cabinet at a time, and follow the installation stages in order, without modification. During installation, be careful to keep the relevant fittings for the current cabinet together. Do not over tighten screws, and ensure that any larger panels are laid flat and protected.

Clean the cabinets with a damp cloth, and if necessary a small amount of liquid soap, only. Do not use abrasives. We provide a full cleaning and aftercare guide on our website, please view this for further information.

2145mm full height cabinet


2145mm full height cabinet panels


2145mm full height cabinet hardware


2145mm full height cabinets - shelves

Please Note:

Shelves can be mounted using the cam housing shown in the points marked [A] with dowels for additional support (marked [E] ). There are two allocated slots for shelves fitted with cam housing.

If additional shelves are required, they can be mounted with dowels.

Shelf position cannot be altered after cabinet assembly is completed.

The diagram above illustrates the allocated positioning of shelves.

Step one:

Insert [A] and [E] as shown in the diagram below for both side panels (1)

Apply a small drop of glue to each dowel [E] before inserting.

2145mm full height cabinet - step one

Note: Fittings for shelves should be placed as required. Shelf (3) can only be placed in two locations, whereas shelf (4) can be fitted in any of the shelf locations. Please view the shelves section of this manual for more information.

Step two:

Insert [B] as shown ensuring the arrow marking is pointing towards the outside edge for top and bottom panels (2)

2145mm full height cabinet - step two

Step three:

Insert [B] as shown ensuring the arrow marking is pointing towards the outside edge for shelf panel (3)

2145mm full height cabinet - step three

Step four:

Connect the top and base panel (2) to the side panel (1) using the fittings inserted during steps 1 and 2.

Repeat the process for all shelf panels (3) and (4)

2145mm full height cabinet - step four

Step five:

Slide the back panel (5) between the grooves on the inside edge of panels (2)

It is advised that you run a small amount of glue along the grooves first.

2145mm full height cabinet - step five

Step six:

Connect the opposite side panel (1) as shown then tighten all fittings [B] by turning in direction of arrow with a screwdriver.

2145mm full height cabinet - step six

Fitting Cabinet Legs:

Position each foot mount [H] towards the edge of the base panel at each corner. Ensure screw holes are not aligned over the panel join and that the overhand foot support is overlapping the side panel as shown below.

Drill 3mm pilot holes into the base panel through the four mounting holes in each foot mount. Now screw the four [C] screws supplied with each foot directly through the foot mount and into the base panel.

Attach the adjustable legs [I] to each foot mount and adjust to the appropriate height.

fitting cabinet legs

Joining Cabinets:

Cabinets should be joined between each set of hinge holes on the inside edge of the side panel as shown in the diagram. Mark 25mm as a guide on a 3mm diameter drill bit using masking tape. Drill between the hinge holes into the cabinet side panel (18mm) and 7mm into the next until you reach the marker. Join the two cabinets together using the 25mm screws provided [D]

joining cabinets

Fitting Cabinet to Wall:

When fixing the cabinet to the wall you must only use slotted angle brackets. A round head screw must be used to fix the bracket.
It is important that you use the slot that runs at perpendicular to the width (across and not parallel with the grain).

fitting cabinet to wall

Fitting Plinths:

Secure plinth to plinth clip [J] using screw provided [C].
Clip each plinth clip onto the legs [I] at the front of the cabinet.

fitting plinths
back to the topBack to Top

Easy to buy online - Follow our 4 simple steps to order your kitchen

choose your door type and finishPick from 'Shaker' or 'Traditional' door styles; available in a choice of sanded, lacquered, or painted finishes (using Farrow & Ball colours).Choose your door type and finish. choose your drawer typesNext pick from a comprehensive range of oak drawers, including single and double height, with a choice of oak, stainless steel or standard grey sides.Choose your drawer type. Add your unit and accessoriesFinally, choose suitable solid oak cabinets, additional specialist units and matching accessories from our wide range, then finalise your order.Add your units to the basket. Get your kitchen within 10 daysOnce your order is complete our specialist team will deliver your order direct to your door within 10 working days.Receive your kitchen within 10 working days!